AIR CONDITIONING SIZE AND YEAR What year and size is the Air Conditioning system? Let me show you how YOU the Realtor can determine that on your own.  Remember that these dates are NOT installation dates, but they are the manufacture date and typically these dates are close to each other. First let us understand “Tonnage” is: Tonnage  The unit of measure used in air conditioning to describe the cooling capacity of a system. One ton of cooling is based on the amount of heat needed to melt one ton (2000 lbs.) of ice in a 24 hour period. One ton of cooling is equal to 12,000 Btu/hr. This size of an Air Conditioning Unit is based up many factors, such as composition of the building, which way it faces, the number of windows, the amount of insulation..... Basic Principals of Air Conditioning: The basic principals of the Air Conditioning System used for Florida.An AC system is used as a dual purpose.One is to allow warm air to be pulled into the system, filter this air and then flow across the cold coils and blow cold air into the building.

The other purpose is to pull the humidity out of the air.This is VERY important.So with this information – BIGGER IS NOT BETTER!A house with to large an AC system will always be damp and contain that “bone chilling” cold.If in doubt call a Professional and licensed Heating, and Air Conditioning (HVAC) contractor. How to determine the age and size of the AC unit: The age or manufacture date of an AC compressor is usually coded under the serial number portion of the data plate that is present on the side of the compressor (Outside AC portion of the AC system) The red boxed area is the Serial Number for this type of unit.The “L” indicates the month of the manufacture.“L” being the 12thletter of the alphabet and the ‘01” being the last 2 numbers of the year, thus meaning this is a December 2001 manufacture date. This is the area where the data or information from above was obtained.The exterior portion of the AC system called the compressor. Congratulations on learning how to determine the age of an Air Conditioning Compressor.The air handler’s age is determined much the same way.

The air handler is located within the interior of the residence most of the time it is in a closet, garage or attic area.This applies to the MAJORITY of AC units in SW Florida.Other types are present, but this will allow you to determine the age of many of the AC systems.window ac unit outlet How to determine the size (called tonnage) of an Air Conditioning system:compact wall ac unit First of all the size of an AC unit is called a ton or tonnage.energy star rated window ac unitsA recap of tonnage is Tonnage  The unit of measure used in air conditioning to describe the cooling capacity of a system. The number to remember is 12,000 BTU’s or more simply 12.If 12,000 BTU’s is equal to 1 (one) ton of AC then 18,000 is equal to 1.5 tons and 24,000 is equal to 2 tons and so on.

Look at the model number (Located on the data plate stamped on the actual side of the compressor) on the compressor and there should be a number divisible by 12.It should start at 18 and not be more than 60 for residential AC units.18 to equal 1.5 tons and 60 to equal 5 tons of cooling. Look at the model number below and you determine the AC compressor size. The 36 in the model number in the first picture above it means that the AC compressor is equal to 3 tons of cooling. Once again, size is very important and detrimental to the proper operational status of an Air Conditioning System.AC Unit Operating Cost Calculator Online calculator to calculate the daily or monthly usage cost of your air conditioning unit. The Ac Operating Cost based on the factors like Equipment Size, Electric Rate, Cooling Hours and SEER (Seasonal Energy Efficiency Ratio). AC Unit Operating Cost Calculation Equipment Size:0.5 Ton 1 Ton1.5 Ton2 Tons2.5 Tons3 Tons3.5 Tons4 Tons4.5 Tons5 Tons

Code to add this calci to your website Energy Consumed Watts = ( Equipment Size / SEER ), Energy Consumed (kWh) = Energy Consumed Watts / 1000, Cost = Energy Consumed (kWh) x Hours x Electric Rate. AC unit operating cost calculator helps you to determine the daily and monthly usage cost of your air conditioner. Wind Chill Calculator Room Air Conditioner(AC) Calculator Rain Harvest AC Tonnage Calculator Cloud BaseI have read & accept Please enter your email address you registered with and we will send the instructions Personal InformationAddress BookMy WishlistMy OrdersGift Card Balance Appliances HOME APPLIANCESAir Conditioners Exclude Out of Stock 1.1 Ton 1.8 Ton 2.2 Ton 0.75 Ton 1 Ton 1.5 Ton 1.25 Ton 2 Ton Samsung LG Whirlpool Godrej Videocon Voltas Haier Hitachi Ogeneral Panasonic Bluestar Carrier Daikin Electrolux Mitsubishi Vestar VISE Invertor 5 Star 4 Star 3 Star 2 Star 1 Star Price(Low to High ) web design by aurus

What Tonnage Do I Need? An air conditioner’s capacity is measured in tons, but this measure doesn’t refer to its weight. In this case, a ton is a number that represents how much heat a unit can remove in an hour. To determine how much tonnage your air conditioner needs to efficiently cool down your house, you must take into account both square footage of your space, and the climate where you live. Warmer climates require higher tonnage to efficiently remove heat from large homes or offices with a lot of square footage. South Florida’s year-long tropical climate makes cooling indoor air more challenging. Air conditioners that are 1.5 tons can cool off a space that is 600-900 square feet. Units that are 2 tons can cool off 901-1200 square feet spaces. Units that are 2.5 tons can cool off 1201-1500 square feet, etc. This pattern continues up to units of 5 tons that cool off 2401-3000 square feet, with every half ton increase adding about an additional 300 square feet. It’s important that the right sized air conditioner or heat pump is installed into your home for maximum energy efficiency benefits.